Evening...

In this clip: http://www.youtube.com/watch?v=kxLUVP-G6Vc
demon has a small "ups counter" on the bottom left and when his health is over +/-150 it's shown in light blue.

If I wanted to edit those into my config, do i have get a hud editor or can it be done with the console?

Anyone know how to do it?

Greetings

I'm still batteling to get the QuakeLive stutter free. In Q3 all I needed to set was:
1) r_displayrefresh 75
2) com_maxfps 75
3) 1024 x 768 res
4) m_filter 1
5) cg_fov 85

But now in QL these values doesn't smooth out the graphics at all.

Is this due to input lag from the mouse side? (like the mouse needs to be set to a higer response time)
Is the FOV causing this on the 1024 x 768 res?
Or is this because the game runs in a browser?
It doesn't look like there is a cure, as I've asked this question on the QL Forums too.

:(

(sucks)

Hello

I have looked everywhere with the help of google, but can't seem to find out what is wrong with my sound. It's like the game is set to low quality audio.

I tried a reinstall - and saw that with the earlier version of Q3A there was a A3D setting, but it's not in the new 1.32 point release.

I've went through all the s_ commands but nothing changes the "fat" low quality beeps in the menu and in-game sounds.
Ever since i reinstalled the game the sound has gone like it's on 8bit instead of 16bit
Any suggestions?

Thanks

Evening.


Upon getting myself a 19" Samsung 19" 953 LCD I need to redo my Video settings for Quake 3

I used to have a very smooth Quake with my CRT monitor when it was still working with these following settings:

Com_maxFPS 100
r_displayrefresh 100

This reduced the amount of jitter quake made when moving around.
The CRT was set to 650 res.
I found that keeping the "max_FPS" and "r_displayrefresh" the same Quake performed much smoother.

But now I sit with an LCD that can do only 75Hz. (I know LCD's doesn't work with refresh rates but in Quake it does make a difference)
I have my maxFPS locked at 75 and refresh rate the same, but it's too low to make the game smooth.
What I`m asking for is a possible solution to all this drama. Is there any way to get it smooth again like I had it on the CRT?

I've been reading around on google and some ppl uses "r_mode -1" But upon trying that I get an open GL crash message, trying the other "r_modes xx" just seems to make the resolution either higher or the refresh rate too high for my monitor to handle.


I`m really fed-up by now.

Thank you.

<3333

Haro

I only have 1 config "q3config" And the setting for the LG is "cg_altlightning 0" in the menu of cpma i see that CPM Lightning option is off when i open quake3 each time. Problem is it keeps changing to that crappy distorted look, instead of the thin one. I sometimes get the OPS lg look if i goto the menu and set the CPM lightning on which is actually the one I prefer, but i know it's been taken out of CPMA. which makes me believe that my Q3 config setting with LG is totally fooKi'd

Any idea how to get it sitting at THIN permanently?

With the cg_altLightning 1 The LG goes into CPMA style
and wilth cg_altLightning it is supposed to go to Original Q3 right?

That part makes perfect sense. However the new Version 1.44 does not have the setting to set the LG to original Q3's look, or so it seems to be in my case.

How can I get it back to the default look again?

I'll upload a pic of what it looks like with cg_altLightning 0
(it's ugly as hell)

Gametype: Duel
Map: ztn3tourney1 - Blood Run
Mod: N/A
Viewpoint: LavAzza
Version info: CMPA 1.40
How to play back Q3 demos


My first game in an online tourey on the South African server Kalahari. Yes I’m very unproven and just enjoying the game. I guess we’re lucky to have an active Quake 3 community here.

Could someone host me a COPY?

CPMA and OSP just did not work...
i wana redo everything.